background image

50

Poor audio quality. Speech is cutting out.

•  You may be close to being out of range of the base station. Try moving 

closer.

•  Other electronic products can cause interference with your handset. Try 

installing the base station far away from devices such as TVs, microwaves, 

or other cordless devices, including other handsets.

•  If the problem persists, contact your system administrator.

Technical Specifications

RF frequency band

1921.536–1928.448 MHz

Channels

5

Operating temperature

32–122 °F (0–50 °C)

Power requirements

Base: 5.0 Vdc @ 800 mA 

Handset charger: 6.0 Vdc @ 300 mA 

Handset: 2.4 V 550/750 mAh, Ni-MH battery pack

Power over Ethernet

IEEE 802.3at supported, class 3

Ethernet network port

10/100 Mbps RJ-45 port

Special characters

Entering special characters

When entering text using the dial pad, the following special characters are 

available. Press the 1, 0, or pound sign (#) keys to enter special characters.

Key Characters

1

~ ^ ` % ! & - _ + = |

0

 0 : ; , ? . @ *

#

( ) [ ] { } < > / \ #

Press star ( ) to switch between uppercase and lowercase/European characters.

Summary of Contents for VSP60





















































Reviews: