background image

EN - 3

En

g

lish

when the adapter is plugged into the power 
outlet, or when the handset is replaced in its 
cradle. This is a common event associated 
with the closing of any electrical circuit. The 
user should not plug the phone into a power 
outlet, and should not put a charged handset 
into the cradle, if the phone is located in 
an environment containing concentrations 
of flammable or flame-supporting gases, 
unless there is adequate ventilation. A spark 
in such an environment could create a fire or 
explosion. Such environments might include: 
medical use of oxygen without adequate 
ventilation; industrial gases (cleaning 
solvents; gasoline vapors; etc.); a leak of 
natural gas; etc.

16. Only put the handset of your telephone next 

to your ear when it is in normal talk mode.

17. The power adapters are intended to be 

correctly oriented in a vertical or floor mount 
position. The prongs are not designed to 
hold the plug in place if it is plugged into a 
ceiling, under-the-table or cabinet outlet.

18. Use only the power cord and batteries 

indicated in this manual. Do not dispose 
of batteries in a fire. They may explode. 
Check with local codes for possible special 
disposal instructions.

19. In wall mounting position, make sure to 

mount the telephone base on the wall by 
aligning the eyelets with the mounting studs 
of the wall plate. Then slide the telephone 
base down on both mounting studs until it 
locks into place. Refer to the full instructions 
in Installation in the user’s manual.

20. This product should be mounted at a height 

of less than 2 meters.

 

 

CAUTIONS

 CAUTIONS

•  Keep small metallic objects such as pins and 

staples away from the handset receiver.

SAVE THESE INSTRUCTIONS

Summary of Contents for Analog Next Gen C5012









































Reviews: