background image

SPECIFICATIONS

Wingspan:......................................1540mm 
Length:...........................................1120mm 
Electric Motor:.....................See next pager
Glow Engine:....................  .46 2-T / .70 4-T

Radio:....................6 Channel / 8-9 Servos
Function: Ailerons-Elevator-Rudder-Throttle
Flaps.

WARNING!

 This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and

cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! 

Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,

die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen. Bei unsachgemässer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstätzung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

Radio control model / Flugmodel

ALL BALSA, PLYWOOD CONSTRUCTION AND ALMOST READY TO FLY

 

JAPANESE DIVE BOMBER

Instruction manual / Montageanleitung

TECHNISCHE DATEN

Spannweite:...................................1540mm
Lange:............................................1120mm
Elektroantrieb.............(siehe nächste Seite)
Verbrennerantrieb:...............7.45cc - 11.5cc
Fluggewicht:.......................................3.5Kg
Fernsteuerung..........6 Kanal / 8-9 Servos

VQ No: VQA138 GREEN

AICHI D3A1 “VAL”

RTF Weight: 3.5Kg (will vary with equipment
use)

VQ No: VQA138 GRAY

Summary of Contents for AICHI D3A1 VAL VQA138 GREEN




















Reviews: