background image

 

VPI Industries, Inc. Limited Warranty 

VPI Industries, Inc. (VPI) warrants this unit against defects in materials and/or workmanship for three (3) years from the 
date of purchase by the original retail purchaser. VPI’s sole obligation under this warranty is limited to the repair or 
replacement, at VPI’s option, of any part(s) found to be defective. VPI’s obligation to repair or replace defective parts is the 
purchaser’s sole and exclusive remedy, and VPI shall not be liable for any direct or indirect injury and/or property damage 
arising out of the use of the product or defect in or failure of the product.  
This warranty does not extend to any unit whose serial number has been defaced or altered. Any product that VPI 
determines causes a defect or malfunction due to incorrect installation, modification, misuse, or servicing by the purchaser, 
or service technician not authorized by VPI to perform such service will not be warranted. This warranty does not cover 
trivial or cosmetic defects that do not impair the unit’s normal function. 
VPI reserves the right to make changes in this product without assuming any obligation to install such change in any product 
previously manufactured. This warranty to repair or replace defective parts is in lieu of all other express or implied 
warranties of merchantability or fitness for a particular purpose. There are not warranties that extend beyond the description 
herein. 
Some states do not allow exclusion of implied warranties or limitation of incidental or consequential damages, so the above 
exclusion or limitations may not apply to you. This warranty gives you specific legal rights, and you may also have other 
rights that vary from state to state.  
 

Register your Product Online: 

http://vpiindustries.com/warranty/

 

 

 

Summary of Contents for HR-X











Reviews: