background image

128-9304

 14 of 28

14

Factory Lock Relay

Factory Unlock Relay

87a

87

30

85

86

87a

87

30

86

85

From Fuse Box + 12 Volts

Lock

Unlock

To Red Lock Wire 

Of Control Module

To Green Unlock Wire 

Of Control Module

  

3 Pin Door Lock/Unlock Harness:

 (White Connector) 300mA   

Part # 1122906

 1 Red Wire: 

(-) Lock 

The Red wire provides a (-) Negative Pulse when the transmitter is used to lock the doors.

 2 Green: 

(-) Unlock

The Green wire provides a (-) Negative Pulse when the transmitter is used to unlock the doors. 

 3 Red/Black: 

(-) Second Unlock

The Red w/Black trace wire will provide a (-) Negative Pulse when the transmitter unlock button is pressed 

a second time directly following a first unlock if the feature is selected at time of installation.  This feature 

is used for second step unlock, (all doors unlock),  in a two step unlock circuit.  In this arrangement, Red 

is used to control the drivers door unlock relay, and the Red/Black will be used to control the unlocking 

of all other doors. 

 3 Wire Ground Switched Door Lock Circuits:

In this application, the Red wire of the door lock harness provides a ground pulse during the arming se-

quence, or pulsed ground lock output.  Connect the Red wire to the low current ground signal wire from 

the factory door lock switch to the factory door lock relay.

The Green wire of the door lock harness provides a ground pulse during the disarming sequence, or 

pulsed ground unlock output.  Connect the Green wire to the low current ground signal wire from the 

factory door unlock switch to the factory door unlock relay.  See the following diagram for Wiring Detail.

3 Wire Ground Switched Door Lock/Unlock Wiring Detail

 

Driver Priority Unlocking:

For driver Priority Unlocking the Red/Black wire will be connected to unlock all doors, and the green will 

be used to unlock the drivers door.  Please review the reference diagrams shown next and wire according 

to the vehicle's unlocking circuit.

Summary of Contents for PRO9276E Pursuit Series





























Reviews: