the appliance
• Use a suitably sized multi-polar switch with
minimum contact gaps of 3 mm to install the
appliance.
• Switch off the appliance at the installation's main
switch: a) if the appliance does not function
correctly; b) before cleaning the outside of the
appliance, c) if the appliance is not to be used for
any length of time.
• Ensure that the room has an adequate source of
fresh air to ensure correct appliance operation. In
the event that other non-sealed combustion-based
appliances (such as water heater or gas stove) are
installed in the same room, check that air
replacement is sufficient for all appliances to work
effectively together.
• The appliance cannot be used to control activation
of water heaters, room heaters, etc. and it must not
exhaust into the hot air flues.
• Ensure that the appliance discharges into a single
duct (dedicated to this product) or directly to the
outside.
• The air to be extracted from the room must be clean
(i.e. free of grease, soot, chemical and corrosive
agents, and explosive or flammable mixtures).
• Do not cover or block appliance intake or outlet
vents grilles as this may prevent optimum air flow.
• Specifications
for
the
power
supply
must
correspond to the electrical data on data plate A
(Fig.A)
N.B.
•
If the appliance is installed between a wall and
wall tiling, fit a spacer to compensate for any
level differences to ensure correct operation.
•
Ariett: if the unit is to be mounted on the ceiling,
replace the mylar spring (already fitted to
thefan),with the thicker one contained in
theaccessories bag. (Fig.10)
Installation
Fig. 1-31.
Maintenance / Cleaning
Fig. 32-38.
Important information
concerning the environmentally
compatible disposal
IN CERTAIN EUROPEAN UNION COUNTRIES THIS
PRODUCT DOES NOT FALL WITHIN THE
REQUIREMENTS OF THE NATIONAL LAWS
IMPLEMENTING DIRECTIVE WEEE, AND IN
THESE COUNTRIES THE PRODUCT IS NOT
SUBJECT TO SEPARATE DISPOSAL OPERATIONS
AT THE END OF ITS WORKING LIFE.
This product conforms to EU Directive2002/96/EC.
This appliance bears the symbol
of the barred waste bin. This
indicates that, at the end of its
useful life, it must not be disposed
of as domestic waste, but must
be taken to a collection centre for
waste electrical and electronic
equipment, or returned to a
retailer on purchase of a replacement.
It is the user's responsibility to dispose of this
appliance through the appropriate channels at the
end of its useful life. Failure to do so may incur the
penalties established by laws governing waste
disposal.
Proper differential collection, and the subsequent
recycling,
processing
and
environmentally
compatible disposal of waste equipment avoids
unnecessary damage to the environment and
possible related healthrisks, and also promotes
recycling of the materials used in the appliance.
For further information on waste collection and
disposal, contact your local waste disposal service,
or the shop from which you purchased the appliance.
Manufacturers
and
importers
fulfil
their
responsibilities for recycling, processing and
environmentally compatible disposal either directly or
by participating in collective systems.
7
ENGLISH
Summary of Contents for ARIETT HABITAT 15/30 LL
