EN
9
WWW.VONROC.COM
tool and hold the power tool motionless until the
wheel comes to a complete stop. Never attempt
to remove the cutoff wheel from the cut while the
wheel is in motion otherwise kickback may occur.
Investigate and take corrective action to eliminate
the cause of wheel pinching or snagging.
f)
Do not restart the cutting operation in the
workpiece. Let the wheel reach full speed and
carefully reenter the cut.
The wheel may bind,
walk up or kickback if the power tool is restarted
in the workpiece.
g)
Support panels or any oversized workpiece to
minimize the risk of wheel pinching and kick
back.
Large workpieces tend to sag under their
own weight. Supports must be placed under the
workpiece near the line of cut and near the edge
of the workpiece on both sides of the wheel.
h)
Use extra caution when making a “pocket cut”
into existing walls or other blind areas.
The prot-
ruding wheel may cut gas or water pipes, electri-
cal wiring or objects that can cause kickback.
ADDITIONAL SAFETY INSTRUCTIONS FOR
WIRE BRUSHING OPERATIONS
Safety warnings specific for wire brushing operations:
a)
Be aware that wire bristles are thrown by the
brush even during ordinary operation. Do not
overstress the wires by applying excessive load
to the brush.
The wire bristles can easily pene-
trate light clothing and/or skin.
b)
Allow brushes to run at operating speed for at
least one minute before using them. During
this time no one is to stand in front or in line
with the brush.
Loose bristles or wires will be
discharged during the run-in time.
c)
Direct the discharge of the spinning wire brush
away from you.
Small particles and tiny wire
fragments may be discharged at high velocity
during the use of these brushes and may beco-
me imbedded in your skin.
FOR THE CHARGER
Intended use
Charge only rechargeable battery packs. Other
types of batteries may burst causing personal
injury and damage.
a)
The appliance is not to be used by persons (in
cluding children) with reduced physical, sensory
or mental capabilities, or lack of experience and
knowledge, unless they have been given super
vision or instruction
b)
Children being supervised not to play with the
appliance
c)
Do not recharging nonrechargeable batteries!
d)
During charging, batteries must be placed in the
well ventilated area!
e)
Integrated batteries may only be removed for
disposal by qualified personnel.
Opening the
housing shell can destroy the power tool.
To remove the battery from the power tool, press
the On/Off switch (5) until the battery is fully
discharged. Unscrew the screws on the housing
and remove the housing shell in order to remove
the battery. To prevent a short circuit, disconnect
the connectors on the battery one at a time and
then isolate the poles. Even when fully dischar-
ged, the battery still contains a residual capacity,
which can be released in case of a short circuit.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions.
Always check that the power supply
corresponds to the voltage on the rating plate.
Your machine is double insulated, therefore
no earthwire is required.
2. MACHINE INFORMATION
Intended use
This power tool is intended to function as a grinder,
sander, wire brush, polisher, carving or cut-off tool.
This combitool is great for editing of materials like
wood, plastic, stone, shell aluminium, brass and steel.
Always use the proper accessories and speed setting.
TECHNICAL SPECIFICATIONS
Model No.
CT503DC
Rechargeable Battery
4V Li-ion 600mAh
Battery charging time
2 hours
Maximum disc diameter
Ø35 mm
Maximum drill diameter
Ø2.3 mm
No load speed
5000/10000/15000/min
Capacity of spring chuck
2.3 mm
Weight
0.1 kg
Summary of Contents for CT502DCl
