EN
7
WWW.VONROC.COM
b) Never place your hand near the rotating acces-
sory. Accessory may kickback over your hand.
c)
Do not position your body in the area where po-
wer tool will move if kickback occurs. Kickback
will propel the tool in direction opposite to the
wheel’s movement at the point of snagging.
d) Use special care when working corners, sharp
edges etc. Avoid bouncing and snagging the
accessory. Corners, sharp edges or bouncing
have a tendency to snag the rotating accessory
and cause loss of control or kickback.
e)
Do not attach a saw chain woodcarving blade or
toothed saw blade. Such blades create frequent
kickback and loss of control.
Safety Warnings Specific for Grinding and Abrasive
Cutting-Off Operations:
a)
Use only wheel types that are recommended
for your power tool and the specific guard
designed for the selected wheel. Wheels for
which the power tool was not designed cannot
be adequately guarded and are unsafe.
b) The grinding surface of centre depressed
wheels must be mounted below the plane of
the guard lip. An improperly mounted wheel
that projects through the plane of theguard lip
cannot be adequately protected.
c)
The guard must be securely attached to the po-
wer tool and positioned for maximum safety, so
the least amount of wheel is exposed towards
the operator. The guard helps to protect the
operator from broken wheel fragments, acci-
dental contact with wheel and sparks that could
ignite clothing.
d) Wheels must be used only for recommended
applications. For example: do not grind with the
side of cut-off wheel. Abrasive cut-off wheels are
intended for peripheral grinding, side forces ap-
plied to these wheels may cause them to shatter.
e)
Always use undamaged wheel flanges that
are of correct size and shape for your selected
wheel. Proper wheel flanges support the wheel
thus reducing the possibility of wheel breakage.
Flanges for cut-off wheels may be different
from grinding wheel flanges.
f)
Do not use worn down wheels from larger po-
wer tools. Wheel intended for larger power tool
is not suitable for the higher speed of a smaller
tool and may burst.
Electrical safety
When using electric machines always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions and
also the enclosed safety instructions.
Always check that the voltage of the power
supply corresponds to the voltage on the
rating plate label.
Class II machine - Double insulation - You
don’t need any earthed plug.
2. MACHINE INFORMATION
Intended use
Your angle grinder has been designed for grinding
masonry and steel materials without the use of
water. For cutting, a special protection guard must
be used (not included)
TECHNICAL SPECIFICATIONS
Model No.
AG502AC
Mains voltage
220-240V~
Mains frequency
50 Hz
Power input
650 W
No-load speed
12.000/min
Grinding disc
Diameter:
Bore:
125 mm
22.2 mm
Spindle thread
M14
Weight
1.69 kg
Noise and vibration
Sound pressure level L
PA
86 dB(A), K=3dB(A)
Acoustic power level L
WA
97 dB(A), K=3dB(A)
Vibration
2.48 m/s
2
, K=1.5 m/s
2
Wear hearing protection.
Vibration level
The vibration emission level stated in this instruc-
tion manual has been measured in accordance
with a standardized test given in EN60745; it may
be used to compare one tool with another and as
a preliminary assessment of exposure to vibration
when using the tool for the applications mentioned.
Summary of Contents for AG502AC
Page 2: ...WWW VONROC COM 2 13 13 A C 6 1 5 2 3 4...
Page 3: ...WWW VONROC COM 3 4 3 10 9 7 8 11 12 4 2 B...
Page 30: ...30...