Vonets VAP11S Quick Setting Manual Download Page 21

 
VONETS

——

WiFi Bridge/Repeater/Router

 

 

18 

 

device will automatically exchange to the same channel as the source WiFi hotspot, 
to make the performance better; 

  Reason 4. There are several WiFi hot spot around the device, WiFi channel mutual 

interference, make the performance worse. At this time, you can try to change 
the source WiFi hot spot and this device WiFi channel to make the performance 
better; 

  Reason 5. The configured source WiFi hot spot parameters are not correct. At this 

time, just need to configure the correct parameters then reboot. 

5. 

The smart phone or PC has been connected the device by WiFi or Ethernet cable, but 
user 

can’t log in the device WEB page, or after log in the WEB it shows error? 

 

Reason 1. The users don’t use the browser recommended by VONETS(IE,Google 
Chrome, Safari, the mobile phone browser); 

  Reason 2. The smart phone or PC installed the firewall, the security level is set too 

high, caused the above problem. At this time, only need to close the firewall; 

  Reason 3. The security level of browser is too high, it will also cause the above 

problem. At this time, just need to reduce the browser’s security level, then log in 
again; 

  Reason 4. The IP address of the device input error. For the new device from the 

factory, user only need input the correct IP address according to the instruction 
guide; for the device that has connected the source hot spot, user only operate 
according to 

<Remark 2>

Summary of Contents for VAP11S






















Reviews: