Volvo Penta D7A T Operator'S Manual Download Page 62

Page: 62 / 116

Lubrication System

Oil change intervals can vary depending on oil quality,
refer to

Lubrication System

Oil change intervals must never exceed a period of 12
months.

If you want longer oil change intervals than stated in
the table

Lubrication System

, the oil change interval

can under certain conditions be increased. To see if
the engine complies, Volvo Penta oil analysis need to
be performed. Contact your Volvo Penta dealer for
further information.

Engine Oil, Change

Always observe the recommended oil change interval.
Use the oil drain pump to drain the oil from the sump.

IMPORTANT!

Only use recommended grades of oil (refer to chapter

Technical Data, page 102

1 Warm the engine up (this makes it easier to pump

the oil from the sump). Then stop the engine.

2 Connect a hose to the outlet pipe of the oil drain

pump. Pump the oil out.

3 Change the oil filters at every second oil change

(refer to section

Oil filter, Change, page 61

4 Fill up with oil to the correct level.

5 Start the engine and allow it to idle. Check the oil

pressure and that there is no leakage by the filters.

6 Stop the engine. Wait a few minutes before you

check the oil level. Top up if necessary.

NOTICE!

Process the old oil and discarded filters in

accordance with local regulations.

Maintenance

47713337 03-2021 © AB VOLVO PENTA

Summary of Contents for D7A T





















































































































Search results

Summary of Contents for D7A T

Reviews:

Related manuals for D7A T

Brands by name

Popular brands

Volvo Penta D7A T, Operator'S Manual

Search results

Summary of Contents for D7A T

Reviews:

Related manuals for D7A T

Brands by name

Popular brands