background image

Seawater Filter, Check and Cleaning

FSC water filter is fitted to the engine this must be
cleaned according to the maintenance schedule.
If the waters where the boat is used contain a lot of
contamination, seaweed etc., the filter must be
checked more often than indicated in the maintenance
schedule. Otherwise there is a risk that the filter may
become blocked, resulting in engine overheating.

Close the sea cock.

Unscrew the cover (A).

Remove the sealing plate (B).

Lift out the insert (C) and clean it.

Install in the reverse order and tighten the cover by
hand.

Open the sea cock and check that there are no leaks
when the engine is being started.

NOTICE!

 Check the hose clamps are tight and water

hose(s) undamaged.

Cooling water intake

Check the cooling water cock operation at every
service.
It must be possible to open and shut the cock for e.g.
impeller maintenance.

Clean the cooling water intake (outer grille) when the
boat is on dry land.

NOTICE!

 Check the hose clamps are tight and water

hose(s) undamaged.

P0030928

 

P0026225

 

Cooling System

47708114 06-2021  © AB VOLVO PENTA

59

Summary of Contents for D1 Series



























































































Reviews: