Volvo Penta 22 Series Instruction Book Download Page 48

Page: 48 / 66

3
4

MS25

HS25

Oil level. MS25 and HS25

Remove the dipstick by turning/screwing it anti
clockwise. Dry off the dipstick and reinstall it in the
reverse gear,

without screwing it into place.

Remove the oil dipstick again and check the oil level.
The correct oil level is between MAX and MIN
marking for the

HS25

and at the level marking for the

MS25.

If necessary the oil is filled through the hole for the
dipstick. For oil quality and capacity: See the chapter
”Technical Data”.

IMPORTANT!

Never overfill reverse gear. The

oil level should always lie within/at the
recommended level.

Oil change and filter cleaning. HS25

1. Clean around the cover (2) so that there is no risk

of the dirt falling into the filter housing.

2. Undo the screws (1). Remove the cover (2) and

gasket (3).

3. Carefully remove the filter (4). Clean the filter in

kerosene (leave the gasket (5) in place). Clean the
filter housing.

4. Suck up oil using an oil pump through the hole for

the dipstick.

5. Measure out the correct amount of oil and fill up

through the hole for the oil dipstick or filter housing.
For oil quality and capacity: See the chapter
”Technical Data”.

IMPORTANT!

Never overfill reverse gear.

6. Reinstall the filter (4) with gasket (5) in the filter

housing. Check that the filter bottoms correctly.

IMPORTANT!

If the filter does not sit flat

there is a risk of breaking it when the cover
(2) is installed.

7. Center the gasket (3) above the filter. Install the

cover.

8. Move the control lever to the neutral position. Start

engine and run at 1500 rpm for a few minutes so
the reverse gear oil cooler is filled with oil.

9. Stop engine and check oil level. Top up if required.

7738666 - Downloaded from www.volvopenta.com 31/05/2007 12:43:18

Summary of Contents for 22 Series



































































Search results

Summary of Contents for 22 Series

Reviews:

Related manuals for 22 Series

Brands by name

Popular brands

Volvo Penta 22 Series, Instruction Book

Search results

Summary of Contents for 22 Series

Reviews:

Related manuals for 22 Series

Brands by name

Popular brands