Volvo Penta 13L Operator'S Manual Download Page 83

Page: 83 / 122

Alternator Belt, Replace

IMPORTANT:

Always change a belt that is oily, worn or damaged.

1 Disconnect the main switch(es) and check that the

engine is not connected to system voltage.

2 Remove the fan guard and fan ring round the

cooling fan.

3 Remove the belt guard.

4 Place a 1/2" square wrench in the belt tensioner (1).

Lift the wrench up and lift the water pump drive belt
off.

5 Place a 1/2" square wrench in the belt tensioner (2).

Press the wrench down and remove the alternator
belt.

6 Check that the pulleys are clean and undamaged.

7 Press the 1/2" wrench in the belt tensioner (2) down

and install the new alternator drive belt.

8 Lift the 1/2" wrench in the belt tensioner (1) and re-

install the water pump drive belt.

9 Install the belt guards.

10 Install the fan guard and fan ring round the cooling

fan.

11 Start the engine and perform a function check.

Lubrication System

Oil change intervals may vary according to the
lubrication oil grade, fuel sulfur content and running
conditions. Refer to

Oil recommendations

The oil change interval may under certain conditions
be increased. To see if the engine complies Volvo
Penta oil analysis needs to be performed. Contact your
Volvo Penta dealer for further information.

NOTICE!

Oil change intervals must never exceed a

period of 12 months.

Maintenance

47711089 09-2018 © AB VOLVO PENTA

Summary of Contents for 13L



























































































































Search results

Summary of Contents for 13L

Reviews:

Related manuals for 13L

Brands by name

Popular brands

Volvo Penta 13L, Operator'S Manual

Search results

Summary of Contents for 13L

Reviews:

Related manuals for 13L

Brands by name

Popular brands