Volvo Penta 13L Operator'S Manual Download Page 38 | Manualshive

Page: 38 / 122

background image

DCU II (Display Control Unit)

TAD1371-75VE

The Volvo Penta DCU II instrument panel
communicates with the engines control unit and has a
number of functions as control, monitoring and
diagnostics.

NOTICE!

Settings and the type of engine data

presented on the display may vary depending on the
installation and engine model.
Depending on the installation the DCU II can also be
used as presentation display only.

NOTICE!

The menus and illustrations shown here are

the English version. Refer to the section

Settings

to

change the display language.

Turn On/Off the ignition

Start the engine

Reduce engine rpm

Increase engine rpm

Stop the engine

Scroll upwards in menus

Select and confirm in menus

Scroll downwards in menus

Return to previous menu selection

START

STOP

OK

P0018811

Instruments and Controls

36

47711089 09-2018 © AB VOLVO PENTA

«
...
36
37
38
39
40
...
»

Summary of Contents for 13L



























































































































Reviews:

No comments

Related manuals for 13L

Brand: ABB Pages: 8

Brand: phytron Pages: 29

Brand: Grizzly Pages: 2

Brand: Ridder Pages: 16

Air Cooled TR-10D

Brand: Wisconsin Pages: 46

Brand: Selve Pages: 132

Brand: Oxygen Pages: 6

Brand: Rotax Pages: 84

Brand: Rotax Pages: 166

Brand: Seg Pages: 21

Brand: Lycoming Pages: 120

Brand: Volvo Pages: 8

Brand: Robin America Pages: 78

OMA-3815-1000-W

Brand: O.S. engine Pages: 2

Brand: O.S. engine Pages: 22

Brand: O.S. engine Pages: 23

Brand: O.S. engine Pages: 43

Brand: sati Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands