6.
5.
CLEANING THE MOTOR FILTER
• This filter should be cleaned at least twice a year
or when it becomes visibly dirty.
• Always operate the cleaner with filter installed,
otherwise reduced suction or motor damage
may result.
• Disconnect from electrical outlet, before cleaning
the filter.
• Do not use a washing machine to rinse filter.
• Do not use hair dryer to dry it.
1. Remove dust bag by pulling dust bag collar
frame upwards.
2. Pull the filter holder upwards.
3. Remove filter from holder.
4. Rinse filter in lukewarm water and dry the
filter completely.
5. Put back filter into the filter holder and refit.
CLEANING AND REPLACING THE HEPA FILTER
The HePa filter should also be cleaned twice a year,
or when visibly dirty. This will help ensure the best
possible filtration from your Volta.
1. Open the rear hood of the vacuum cleaner and lift
out the HePa filter.
2. To clean the filter, cover it with a sheet of paper with
the frame facing up and tap it against a hard surface.
This will help to dislodge excessive dust and dirt
from the filter.
3. if necessary the HePa filter can be rinsed under a
tap using lukewarm water. always rinse the filter
with the frame facing down and never use cleaning
chemicals. Never scrub or brush the filter.
MAINTENANCE
MAINTENANCE / TROUBLESHOOTING
4. air dry the filter for 24 hours , away from direct
sunlight before reusing it. if the filter appears
damaged it is recommended to replace with
a new filter. To purchase new filters contact
electrolux customer service on 1300 365 305 (aUs)
or 0508 730 730 (NZ).
PRECAUTIONARY MEASURES
if the suction air flow is blocked, you should switch off
the vacuum cleaner at once. First, clear the blockage
from the hose and/or telescopic extension tube before
you attempt to start the vacuum cleaner again.
1. Do not operate the vacuum cleaner too close
to heaters, radiators, cigarette butts, etc.
2. Before you insert the plug into the power socket,
make sure your hands are dry.
3. Before you start using the vacuum cleaner,
please remove large or sharp objects from the
floor in order to prevent damage to the paper bag.
4. When you want to pull the plug from socket,
please do this at the plug itself and not by the
electrical cable.
This vacuum cleaner is equipped with a cable and plug,
which rolls up on activation of the rewind pedal. if the
plug or cable is damaged, the plug and cable assembly
must be replaced by returning the product to your local
authorised electrolux service Provider in order to avoid
a hazard.
WARNING:
On collection of proprietary carpet conditioning
powders, plaster / concrete dust, it is recommended
that the dust bag is changed. some of the preparations
contain substances which while
left in the vacuum cleaner for extended periods could
create damage.
many air fresheners, household deodorants, sprays and
polishes contain highly inflammable gas propellants.
Because of this it is particularly important that these
products are used strictly in accordance with the
relevant manufacturers instructions. it is essential that
none of the above products are sprayed directly into
the vacuum cleaner or any of the filters, hose assembly
or dust chamber.
TROUBLE SHOOTING AND
CUSTOMER INFORMATION
You can perform your own troubleshooting
at home based on the checklist given below. However,
if the problem persists, please
contact electrolux on 1300 365 305 (aUs) or
0508 730 730 (NZ)
PROBLEM
POSSIBLE CAUSES
CORRECTIONS
Vacuum cleaner does
not start.
Plug is not properly connected
to the socket.
Check the plug connection or try another socket.
Thermal protector activated due
to high temperature.
Press the On/Off button and wait 20-30 minutes
for the motor to cool down.
Filter indicator light
stays on.
Dust bag is full.
empty or replace the dust bag.
Filters are clogged.
Clean or replace filters.
Reduction of suction
capacity.
suction hose is blocked.
Clean the hose.
Nozzle is blocked.
Clean the nozzle.
Dust bag is full.
empty or replace the dust bag.
Filters are clogged.
Clean or replace filters.
Hose is damaged or broken.
Change the hose.
Over-heating.
Dust bag is full.
empty or replace the dust bag.
Filters are clogged.
Clean or replace filters.
