background image

Important: Please Read Before Installation

INSTALLATION INSTRUCTIONS

!

w w w . v o l t l i g h t i n g . c o m

Important Safety Instructions

!

- 2 -

VOLT

®

 

Tri-Hub Ultra-Slim Brass Up/Down Light

VAL-2103-0-BBZ

This luminaire is intended for installation in accordance with local codes 

and the National Electric Code (NEC). Failure to adhere to these codes and 

instructions may result in serious injury, property damage and void the 

warranty.

These instructions do not intend to cover all variations in installation, 

operation maintenance or mounting situations.

1.  Make sure the power is turned OFF before installing or servicing this 

luminaire.

2.  WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) 

or more from pool, spa or fountain.

3.  This luminaire is intended to be used only with a power supply 

(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.

4.  Wiring connections must be made with UL listed wire connectors that are 

suitable for outdoor use.

5.  Position the low voltage wire and UL listed wire connector so that it is 

located within 6 inches (15.2 cm) from a building structure, a luminaire 

or fitting.

6.  The main low voltage cable is intended for shallow burial - less than 6 

inches (152 mm).

INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS

Lighted lamp is HOT!

WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.

1.  Turn off/unplug and allow to cool before replacing lamp.
2.  Lamp gets HOT quickly! Contact only switch/plug when turning on.
3.  Do not touch the hot lens, guard or enclosure.
4.  Keep lamp away from materials that may burn.
5.  Do not touch lamp at any time. Use a soft cloth. Oil from skin may 

damage lamp.

6.  Do not operate the luminaire fitting with a missing or damaged shield.

SAVE THESE INSTRUCTIONS

Summary of Contents for VAL-2103-0-BBZ









Reviews: