background image

VOLT

®  

18” Hardscape Mounting Bracket (Stainless Steel)

VAC-HS-6718-YMP

Important Safety Instructions: Read Before Installation

INSTALLATION INSTRUCTIONS

!

w w w . v o l t l i g h t i n g . c o m

This luminaire is intended for installation in accordance with local codes and 
the National Electric Code (NEC). Failure to adhere to these codes and

instructions may result in serious injury, property damage and void the 

warranty.

These instructions do not intend to cover all variations in installation, opera-
tion maintenance or mounting situations. 

1.  Make sure that the power is turned OFF before installing or servicing this 

luminaire. 

2.  Warning: risk of electrical shock.  Install all luminaires 10 feet (3.05M) or 

more from pool, spa or fountain.

3.  This luminaire is intended to be used only with a power supply 

(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.

4. 

DO NOT INSTALL in walls where the capstones overhang the wall less 

than 3/4” [19mm] or under stairs where the tread overhangs the riser 

less than 3/4” (19mm).

5.  Wiring connections must be made with UL listed wire connectors that is 

suitable for outdoor use.

6. 

Position the low voltage wire and UL listed wire connector so that it is 

located within 6 inches (15.2 cm) from a building structure, a luminare, 

or fitting.

7.  The main low voltage cable is intended for shallow burial - less than 6 

inches (152 mm).

- 2 -

Product Dimensions

Package Contents

A.  (1) Luminaire
B. 

(2) Stainless Steel Screws

19”

Summary of Contents for VAC-HS-6718-YMP









Reviews: