background image

 

 

Wedgemaster II Ops Manual 

BLADE SERVICING AND REPLACEMENT

 

 
If the machine no longer slices cleanly or without damage, the blades could be dull and need to be replaced.  
Broken, bent, nicked, or dull blades must be replaced immediately.  Change the complete assembly.   
 
 

 
 
 
 
 
 

 
 
 
 
 

1.  Allow yourself ample room to work on a flat, dry surface. 
 
2.  Turn machine on its side and remove the Pusher Head Assembly.   

 

3.  Remove the two (2) Blade Screws from the bottom of the Base Assembly.  Carefully remove the blade 

assembly by gently pushing up from underneath the Base Assembly.  This will remove the blade assembly 
from the unit. 

 

4.  Install new blade assembly by carefully placing it inside the top of the Base Assembly.  NEVER push down 

on blade assembly when inserting into the base!  Once in place, insert the two (2) blade screws until tight. 

 

DISPOSE OF USED BLADES AND BLADE ASSEMBLIES! 

 
 
 

 
 
 

!

 

DANGER: 

 

HANDLE WITH EXTREME CARE AS BLADES ARE SHARP AND CAN CAUSE 
INJURY OR DEATH IF NOT HANDLED PROPERLY.  ALL OPERATORS OF 
THIS EQUIPMENT SHOULD READ THIS OPERATION MANUAL BEFORE 
OPERATING EQUIPMENT. 

!

 

CAUTION: 

PRIOR TO USING YOUR NEW EQUIPMENT, IT IS IMPORTANT TO CLEAN 
THE UNIT.  WASH NEW BLADES WITH WARM SOAPY WATER AND RINSE 
THOROUGHLY TO REMOVE THE THIN PROTECTIVE OIL FILM. 

Summary of Contents for REDCO WEDGEMASTER II









Reviews: