background image

 

COPYRIGHT 

 

All rights reserved. No part of this publication may be reproduced, stored 

in a retrieval system, or transmitted in any form or by any means, whether 

electronic, mechanical, photo copying, recording or otherwise, without the 

prior written permission of the publisher. 

 

 

FCC WARNING 

 

This equipment has been tested and found to comply with the limits for 

class A device, pursuant to part 15 of FCC rules. These limits are 

designed to provide reasonable protection against harmful interference in 

a commercial installation. This equipment generates, uses and can 

radiate radio frequency energy and, if not installed and used in 

accordance with the instructions, may cause harmful interference to radio 

communication. Operation of this equipment in a residential area is likely 

to cause harmful interference, in which case, the user will be required to 

correct the interference at the user’s own expense. 

 

 

CE 

This is a Class A product. In a domestic environment, this product may 

cause radio interference in which case the user may be required to take 

adequate measures. 

 

Take special note to read and understand all content given in the warning 

boxes 

 
 

Warning

 

Summary of Contents for NWT-707





























Reviews: