background image

57

Air conditioner for passenger compartment

Depending on the equipment level, the Transpor-
ter can be equipped with an air conditioning unit 
for the passenger compartment. On the Multi-
van, this is a standard feature.

In addition to air distribution in the bottom area, 
distribution is also channelled upwards to the 
A/C headliner.

A/C headliner

Air conditioner for 
passenger compartment

A/C compressor variants

Manual air conditioning systems and the Clima-
tronic have an internally controlled compressor.

An exception is the 2.5ltr./R5 TDI engine, which 
has an externally controlled compressor, neces-
sary due to the design. The control function is 
integrated in the operating unit.

The externally controlled A/C com-
pressor drive system is described in 
detail in self-study programme 305 
"The R5 TDI engine".

To A/C headliner

Supplementary heater

Due to the high level of efficiency of the TDI 
engines, a fuel powered supplementary heater, 
in conjunction with a 2nd heat exchanger, is 
installed as standard.

As an option, this supplementary heater can be 
upgraded to an auxiliary heater. The heater 
offers the means of preselecting and remotely 
operating heating and ventilation for a limited 
period of up to 30 minutes.

Auxiliary heater

A further option for climate control is a fuel 
powered auxiliary heater, available as an optio-
nal extra. This can be started using the operating 
unit or by radio remote control. The duration of 
operation is unlimited.

310_115

Summary of Contents for Transporter 2004

































































Reviews: