23
6.14 FLUE FAN & MIXER (fig. 35-36)
Carry out component removal procedure as described in 6.4.
Remove the air chamber front cover. Locate and remove the
gas pipe locking pin (
A1
) and swing/rotate the gas pipe away
from the fan assembly (
B1
), (if necessary unscrew the gas
pipe from the gas valve
G1
). Locate and slacken the silencer
(
H1
). Locate and remove the sense electrode. To remove the
fan (
E1
), disconnect the electrical connections attached to
the fan, locate and remove the four screws (
F1
). Gently ease
the fan from its location. To remove the mixer (
C1
) locate and
remove the three screws (
D1
), the mixer can be removed after
the fan removal. Replace in the reverse order. Ensure all seals
are in good condition, taking care to ensure they are replaced
correctly.
6.15 BURNER (fig. 35)
Carry out component removal procedure as described in 6.4.
Remove the air chamber front cover. Locate and remove the
gas pipe locking pin (
A1
) and swing/rotate the gas pipe away
from the fan assembly (
B1
), (if necessary unscrew the gas
pipe from the gas valve
G1
). Locate and slacken the silencer
(
H1
), disconnect the electrical connections attached to the
fan. Disconnect the electrode leads and ancillary wiring from
their respective connectors. Locate and remove the screws
(
I1
) which secure the burner assembly in position to the heat
exchanger (
J1
). Gently ease the fan assembly out of its loca-
tion. Once the assembly has been removed, the burner (
K1
)
can be withdrawn from the heat engine. Ensure the seals (
L1
)
are in good condition, taking care to.
Fig. 34
6.13 ELECTRODES (fig. 34)
Carry out component removal procedure as described in 6.4.
Remove the air chamber front cover. Disconnect the electrode
leads and ancillary wiring from their respective connectors. Re-
move the retaining screws (
V
) for electrode. Remove the spark
ignition electrode (
W
). Remove the flame sensor electrod (
Y
).
6.12 GAS VALVE (fig. 33)
Carry out component removal procedure as described in 6.4.
The gas valve must be changed as complete unit. Disconnect
the electrical plug and leads from the gas valve, slacken and
unscrew gas valve inlet
and outlet connections.
Please note,
the sealing washers (
Q
) must be discarded and replaced with
new sealing washers. Disconnect the compensation pipe (
R
).
Unscrew gas pipe connections (
S-T
), the gas valve can now
be removed. Replace in the reverse order. Check and adjust
burner pressure settings.
WARNING, A GAS TIGHTNESS CHECK MUST BE CAR-
RIED OUT.
6.12.1 INJECTOR (fig. 33)
Carry out component removal procedure as described in 6.4.
Unscrew and remove gas pipe connections (
S-T
). Locate and
remove the injector (
U
) inside the valve. Replace in the reverse
order. Check and adjust burner pressure settings.
WARNING, A GAS TIGHTNESS CHECK MUST BE CAR-
RIED OUT.
Q
Q
U
S
T
C1
D1
E1
F1
V
Y
W
H1
I1
J1
K1
L1
L1
Fig. 33
V
W
Y
Fig. 35
from the PCB, locate and remove the PCB securing screws,
remove the required PCB. Replace in the reverse order ensur-
ing that the position of the 2 control knobs are correctly aligned
with the respective potentiometers on the PCB.
Ensure that the correct jumper tag configuration has been
respected. It will be necessary to check the functioning of the
PCB is set for the correct boiler type/application.
R
Summary of Contents for Vision 25C
Page 39: ......
