background image

Page 6

 

/ PB65XL

 

Vogelzang International Corp. 

VGZ-003 / 20120327.0

CONNECTOR PIPE INSTALLATION

1.  The smooth end of the stovepipe fits over the 

cast iron flue collar at top rear of stove (fig. 5).

 

a).  Crimped end of pipe must be away from 
stove.

 

b).  Hand form lower end (fig. 6) of stove pipe 
to oval shape (fig. 7) and slide over flue outlet 
collar as shown in figure 5.

 

c).  Secure stove pipe to flue collar with  
at least three (3) sheet metal screws and seal 
with stove cement. 

2.  Horizontal pipe runs must slope upwards  

towards the chimney at least 1/4” per foot of 
horizontal run.

3.  You must have at least 18 inches of clearance 

between any horizontal piping and the ceiling.

4.  The pipe cannot extend into the chimney flue 

(figure 8).

5.  Secure pipe/elbow sections with three (3) 

sheet metal screws at each joint to make the 
piping rigid. 

Screws may be no more than a maxi-

mum of 3˝/76mm apart.

6.  It is recommended that no more than two (2) 

90 degree bends be used in the stovepipe in-
stallation. The use of more than two 90 degree  
bends may decrease the amount of draw and 
possibly cause smoke spillage. Where pos-
sible, use only corrugated (nonadjustable) 
elbows. These provide a better seal.

7.  The connector pipe must not pass through 

an attic or roof space, trusses, closet, or any 
concealed space, or floor, ceiling, wall or com-
bustible construction. (See Chimney Connector 

NOTE: CONNECTOR PIPE IS 

NOT INCLUDED

.  

TO PURCHASE PIPE, VISIT YOUR LOCAL 
HARDWARE, HOME OR BUILDING CEN-
TER. SEE “LOCATING STOVE” PAGE 4 FOR  
ADDITIONAL SPECIFICATIONS.

CAUTION: KEEP FURNISHINGS AND OTHER  
COMBUSTIBLE MATERIALS AWAY FROM THE 
STOVE.

Fig. 5 –  Flue Outlet Collar

Fig. 6 –  Hand-form pipe to oval shape – Fig. 7

CORRECT WRONG  WRONG

Fig. 8 – Stovepipe/Flue Connections

Systems & clearances, page 10.) A UL 103 HT 
Listed chimney system 

must 

be used from the 

first penetration of ceiling or wall to the chimney 
cap. Use chimney components from a single 
manufacturer. Do not mix brands.

WARNING: DO NOT USE SINGLE WALL CON-
NECTOR PIPE AS A CHIMNEY - A HOUSE FIRE 
COULD RESULT.

Summary of Contents for PB65XL

















Reviews: