background image

VGZ-018 / 051809.0 

NORSEMAN™ 1500/2500 FuRNAcE

 / 

Page 7

locAtiNg FURNAcE continued…

Fig. 3 – Minimum plenum Clearances from Combustible Materials

wARNINg: RISk OF FIRE

• DO NOT STORE FUEL, FLAm-
mABLE  LIqUIDS  OR  OThER 
COmBUSTIBLE  mATERIALS 
TOO CLOSE TO ThE UNIT.  

•  Keep  furnishings  and 
OThER COmBUSTIBLE mATERI-
ALS OUTSIDE OF CLEARANCE  
DImENSIONS  mARkED  ON 
FURNACE.

•  Before  firing  furnace, 
SLIDE  FIREBRICkS TOwARDS 
REAR  SO  NO  gAPS  REmAIN 
BETwEEN  BRICkS.  DO  NOT 
OPERATE  FURNACE  wITh 
CRACkED  OR  mISSINg  FIRE 
BRICkS.

tools & MAtERiAls REqUiRED FoR AssEMblY  
AND iNstAllAtioN

TOOLS REqUIRED

Safety Glasses
Gloves
Pencil
6 ft. Tape Measure
Tin Snips
Sabre Saw
Drill

1/8” dia. Drill Bit (for sheet metal screws)
Screwdrivers  (Phillips & slotted)
6mm Socket with Driver
10mm Socket with Driver
10mm open end box wrench
7/16” box wrench

mATERIALS REqUIRED

NotE: the following items are Not included with 
your furnace:

chimney connection:  
6” da. minimum 24 MSG black or 26 MSG blue steel 
straight furnace pipe, elbow(s), collar and thimble (as 
required).
6˝ Barometric Draft Regulator (optional)
8˝ Round Butterfly Anti-Backdraft Damper
  (2 required – for parallel installation only)
Plenum & Duct Work with min. temperature rating of 

250° F (as required).

chimney:  Existing  6”  Lined  Masonry  chimney  

or 6” Inside Dia. Listed Type HT chimney.

1/2” Sheet Metal Screws
Electrical Wiring: 16 ga. AWG copper with 90° c min. 

DO NOT use aluminum wire or connectors.

1/2˝ conduit & connectors
Furnace cement (manufacturer recommends Rutland  

code 78 or equivalent)

Summary of Contents for 1500





























Reviews: