VKI Technologies 2001 Operation And Service Manual Download Page 27

Page: 27 / 60

SUPREMA 2001 - OPERATION & SERVICE MANUAL

Suprema 2001 - Operation & Service

July 6, 2001

Page 27 of 60

SETTING LANGUAGE

The messages that appear on the LCD can be displayed in either English or French.
Please note that the coffee maker will be shipped from the factory with the messages
set to English.

To set the language, press the "

" button on the hidden menu scroll

buttons and scroll until the following message appears,

Press the "

START

" button to enter the set mode.

Using the hidden setting adjustment buttons, select “

ENGLISH

”, or

“

FRENCH

”, or “

ENGLISH

FRENCH

”.

To save, press either one of the two hidden menu scroll buttons.

SETTING THE WATER LEVEL PROBE

When scrolling through the "

SET

" mode, you will notice a setting in the menu that

reads,

Press "

START

" to access this menu.

Using the hidden adjustment buttons, change the setting from
"

MECHANICAL SWITCH

" to "

ELECTRONIC PROBE

Exit the “

SET

” mode.

WARNING:

Do not access this menu if the machine is not equipped with the electronic

water level probes.

SET LANGUAGE

PRESS <START>

SET WATER LEVEL

PRESS <START>

Note:

If “

ENGLISH

FRENCH

” is

selected, the
messages on the
display will
continuously
toggle from
English to French
approximately
every three
seconds.

Summary of Contents for 2001





























































Search results

Summary of Contents for 2001

Reviews:

Related manuals for 2001

Brands by name

Popular brands

VKI Technologies 2001, Operation And Service Manual

Search results

Summary of Contents for 2001

Reviews:

Related manuals for 2001

Brands by name

Popular brands