Vivotek IP8330 User Manual Download

Page: 8 / 149

VIVOTEK

8 - User's Manual

Alignment marks

Sunshield

Camera

1. The camera comes with an angled cut sunshield. If you install the camera in a ceiling-mount

orientation, you will need to change the sunshield's orientation.

To adjust the sunshield,

1-1. Loosen the sunshield seal ring using an included acrylic opener.

1-2. You do not need to remove the sunshield. Rotate the protruding ridge to the desired

direction from which sunlight can cause glare.

1-3. Hold the sunshield and the camera using one hand, and then tighten the seal ring using

the same acrylic opener.

Seal Ring

Sunshield

IMPORTANT!

2. Although the camera and the cable gland on the camera's end are waterproof, the cable

molding at the other end is not waterproof.
Measures should be taken to prevent water from leaking in through the cable-end molding,

such as the use of expanding foam sealant, putties, and so on. Note that the cable gland on

the camera should also be securely fastened to attain its waterproof functionality.

Cable Gland

Waterproof

Not Waterproof

Cable Molding

Summary of Contents for IP8330






















































































































































Search results

Summary of Contents for IP8330

Reviews:

Related manuals for IP8330

Brands by name

Popular brands

Vivotek IP8330, User Manual

Search results

Summary of Contents for IP8330

Reviews:

Related manuals for IP8330

Brands by name

Popular brands