Vivotek IP8330 User Manual Download

Page: 57 / 149

VIVOTEK

User's Manual - 57

■

Enable BLC (Back Light Compensation)

: Enable this option when the object is too dark or too bright

to recognize. It allows the camera to adjust to the best light conditions in any environment and

automatically give the necessary light compensation.

You can click

Preview

to fine-tune the image, or click

Restore

to recall the original settings without

incorporating the changes. When completed with the settings on this page, click

Save

to enable the

settings and click

Close

to exit the page.

If you want to configure another sensor setting for day/night/schedule mode, please click

Profile

to open

the Sensor Settings Profile Settings page as shown below.

Please follow the steps beolw to setup a profile:

1. Check

Enable this profile

2. Select the applied mode: Day mode, Night mode, or schedule mode. Please manually enter a range of

time if you choose Schedule mode.

3. Configure Exposure settings in the second column. Please refer to the previous page for detailed

information.

4. Click

Save

to enable the setting and click

Close

to exit the page.

2010/01/13 13:44:17

Summary of Contents for IP8330






















































































































































Search results

Summary of Contents for IP8330

Reviews:

Related manuals for IP8330

Brands by name

Popular brands

Vivotek IP8330, User Manual

Search results

Summary of Contents for IP8330

Reviews:

Related manuals for IP8330

Brands by name

Popular brands