Vivotek IP7161 User Manual Download Page 6

Page: 6 / 164

VIVOTEK

6 - User's Manual

Hardware Reset

The reset button is used to reset the system or restore the factory default settings� Sometimes

resetting the system can return the camera to normal operation� If the system problems remain

after reset, restore the factory settings and install again�

Reset: Press and release the recessed reset button with a paper clip or thin object� Wait for the

Network Camera to reboot�

Restore: Press and hold the recessed reset button until the status LED rapidly blinks� It takes

about 30 seconds� Note that all settings will be restored to factory default� Upon successful

restore, the status LED will blink green and red during normal operation�

SD/SDHC Card Capacity

This network camera is compliant with

SD/SDHC 16GB / 8GB

and other preceding standard SD

cards�

Installation

Hardware Installation

Follow the steps below to

mount the lens to the Network Camera

1� Mount the lens by turning it clockwise onto the camera mount until it stops� If necessary, turn
the lens counterclockwise slowly until it gets the best attitude�
2� Connect the lens cable plug to the camera connector�

Recessed Reset

Button

Status LED

Summary of Contents for IP7161





































































































































































Search results

Summary of Contents for IP7161

Reviews:

Brands by name

Popular brands

Vivotek IP7161, User Manual

Search results

Summary of Contents for IP7161

Reviews:

Brands by name

Popular brands