Vivotek IP7161 User Manual Download

Page: 132 / 164

VIVOTEK

132 - User's Manual

ndo

0/7

number of digital output

naudioin

0/7

number of audio input

naudioout

0/7

number of audio output

nvideoin

0/7

number of video input

nmediastream

0/7

number of media stream per channel

nvideosetting

0/7

number of video settings per channel

naudiosetting

0/7

number of audio settings per channel

nuart

0/7

number of UART interface

nvideoinprofile

0/7

number of sensor profiles

nmotionprofile

0/7

number of motion profiles

ptzenabled

< positive integer >

0/7

An 32-bits integer, each bit can be set

separately as follows:

Bit 0 => Support camera control function

0(not support), 1(support)

Bit 1 => Build-in or external camera.

0(external), 1(build-in)

Bit 2 => Support pan operation. 0(not

support), 1(support)

Bit 3 => Support tilt operation. 0(not

support), 1(support)

Bit 4 => Support zoom operation.

0(not support), 1(support)

Bit 5 => Support focus operation.

0(not support), 1(support)

Bit 6 => Support iris operation.

0(not support), 1(support)

Bit 7 => External or build-in PT. 0(build-in),

1(external)

Bit 8 => Invalidate bit 1 ~ 7.

0(bit 1 ~ 7 are valid),

1(bit 1 ~ 7 are invalid)

Summary of Contents for IP7161





































































































































































Search results

Summary of Contents for IP7161

Reviews:

Related manuals for IP7161

Brands by name

Popular brands

Vivotek IP7161, User Manual

Search results

Summary of Contents for IP7161

Reviews:

Related manuals for IP7161

Brands by name

Popular brands