Vivotek FD8362/62E User Manual Download

Page: 55 / 196

VIVOTEK

User's Manual - 55

► If the default ports are already used by other devices connected to the same router, the Network

Camera will select other ports for the Network Camera�

► If UPnP

is not supported by your router, you will see the following message:

Error: Router does not support UPnP port forwarding.

► Below are steps to enable the UPnP

user interface on your computer:

Note that you must log on to the computer as a system administrator to install the UPnP

components�

1� Go to Start, click

Control Panel

, then click

Add or Remove Programs

�

2� In the Add or Remove Programs dialog box, click

Add/Remove Windows Components

�

3�

In the Windows Components Wizard dialog box, select

Networking Services

and click

Details

�

NOTE:

Summary of Contents for FD8362/62E





































































































































































































Search results

Summary of Contents for FD8362/62E

Reviews:

Related manuals for FD8362/62E

Brands by name

Popular brands

Vivotek FD8362/62E, User Manual

Search results

Summary of Contents for FD8362/62E

Reviews:

Related manuals for FD8362/62E

Brands by name

Popular brands