background image

INSTALLATION 

INSTRUCTION

 

VLMW4065T

CAUTION!

This monitor mount must be securely attached to the vertical wall. If the mount 

is not properly installed it may fall, resulting in possible injury and/or damage.

Note: The mounting components and hardware supplied in this package are not designed for installa-

tions to walls with steel studs or to cinder block walls. If the hardware you need for your installation is 

not included, please consult your local hardware store for proper mounting hardware for the application.

Unpacking Instructions

Carefully open the carton, remove contents and lay out on cardboard or other protective surface 

to avoid damage. Check package contents against the Supplied Parts List in the next page to 

assure that all components were received undamaged.  Do not use damaged or defective parts. 

Important Safety Information  

Install and operate this device with care.  Please read this instruction before beginning the instal-

lation, and carefully follow all instructions contained herein. Use proper safety equipment during 

installation. Please call a qualified installation contractor for help if you don’t understand these 

directions or have any doubts about the safety of the installation. If you are uncertain about the 

nature of your wall, consult a qualified installation contractor. 

Do not use this product for any purpose or in any configuration not explicitly specified in this 

instruction. We hereby disclaims any and all liability or damage arising from incorrect assembly, 

incorrect mounting or incorrect use of this product.

5

• 4 mm Drill bit

• 8 mm Masonry Bit

• Philips Screwdriver

• Stud Finder

• Wrench or Socket Set

• Carpenter’s Level

Tools Required

S

VESA tandard:

 

Weight:

Up to 

65 kg (1453 lbs)

Up to 

600x400

Summary of Contents for VLMW4065T









Reviews: