TM
lutron.com
1. 844. LUTR ON1
M éxi co:
1. 888. 235. 2910
®
LUTRON
PowPak
UL2043
Pl enum Rated
®
FCJS-010
120-277 V 50/60 Hz 1 A
~
12V 25mA
IEC SELV / NEC Class 2
Sensor | Détecteur
®
TM
lutron.com
1. 844. LUTR ON1
M éxi co:
1. 888. 235. 2910
®
LUTRON
PowPak
UL2043
Pl enum Rated
®
FCJS-010
120-277 V 50/60 Hz 1 A
~
12V 25mA
IEC SELV / NEC Class 2
Sensor | Détecteur
®
LUTRON
LUTRON
TM
lutron.com
1. 844. LUTR ON1
M éxi co:
1. 888. 235. 2910
®
LUTRON
PowPak
UL2043
Pl enum Rated
®
FCJS-010
120-277 V 50/60 Hz 1 A
~
12V 25mA
IEC SELV / NEC Class 2
Sensor | Détecteur
®
TM
lutron.com
1. 844. LUTR ON1
M éxi co:
1. 888. 235. 2910
®
LUTRON
PowPak
UL2043
Pl enum Rated
®
FCJS-010
120-277 V 50/60 Hz 1 A
~
12V 25mA
IEC SELV / NEC Class 2
Sensor | Détecteur
®
LUTRON
LUTRON
2. PAIR MODULE AND WALL CONTROLLER
1. Apply power to fan. Press and hold center
button on module for approximately six
seconds until LEDs flash. Release button.
2. Press and hold Off button on wall
controller for approximately six seconds
until LED flashes. Release button. Pairing
is complete.
This procedure can be used to add multiple
wall controllers and/or modules to a group of
up to ten devices.
Center
Module
Button
Fan Off
3. MOUNT WALL CONTROLLER AND ADJUST SETTINGS
Mount Wall Controller
Mount wall controller according to the mounting instructions packaged with the controller.
Adjust Low-End Trim
The fan requires a minimum of 1 V to turn on.
To adjust the module’s low-end trim to at least 1 V:
1. Press wall controller Off button.
2. Press and hold On button and Increase Speed button simultaneously for approximately six seconds until LED
flashes.
3. Slowly tap Increase Speed button nine times to set low-end trim to approximately 1.1 V.
4. Press and hold Off button for approximately six seconds until LED flashes to save the setting.
© 2021 DELTA T LLC ALL RIGHTS RESERVED.
ESS-INST-375-MUL-01 REV A 08/04/2021
The wall controller will not operate the fan(s).
Release wire antenna from front of module and extend it away
from module to extend range of wall controller.
I need to reset the module to factory default
settings.
Quickly press center module button four times and hold button
on fourth press until LEDs flash. Release button. Within three
seconds, quickly press center module button four times and hold
button on fourth press until LEDs flash rapidly. The module is now
reset to factory default settings.
Set Preferred Speed Setting (Optional)
By default, pressing the center wall controller
button sets the fan speed to 50%.
To program a
preferred speed setting:
1. Use speed adjustment buttons to select
desired fan speed.
2. Press and hold center button for
approximately six seconds until LED flashes
to save the setting.
Note: For systems with multiple wall controllers,
each controller can have a different preferred
speed setting.
Fan On (100% Speed)
Decrease Fan Speed
Fan Off (0% Speed)
Increase Fan Speed
50% Speed (Default)
or Preferred Setting
TROUBLESHOOTING
