background image

27

Vibration of the washing
machine

Level the washing machine.
Level the washing machine.
Fasten the footing.
To check if the internal packing for the transportation
have all been removed.

The bubble spills from
the detergent

Check if the detergent is excessive, if it is the specialized
detergent for the cylinder washing machine.
Dip one scoop of the softener mixed with 1/2 liter of
water to the detergent box II.
Reduce the usage amount of the detergent in the next
time's wash.

The machine stops when
the procedure has not
been finished

Power failure or water cut.

The drainage pump has
noise during the
operation when the
water has just been
drained

The inner barrel water of the washing machine has been
drained but there is still a small amount of water in the
drainage pump and pipe. The drainage pump
continuously operates and takes in the air, and at this
time there is the noise, which is normal situation.

To stop for some time
during the wash
procedure

The washing machine adds water automatically.
Because there is too much bubble in the tube, the
washing machine is cleaning the bubble.

If you cannot solve the above abnormal situations, would you please:
1. To turn the procedure knob to  OFF , pull out the attachment plug;
2. To close the water tap, and contact the nearest service center.

5 TROUBLESHOOTING

Summary of Contents for WFL-100623A
































Reviews: