manualshive.com logo in svg

Vivax WFL-1001, Service Manual

Share
Download
Vivax WFL-1001 Service Manual Download Page 40

P.40

Operation step

Picture

　　　　　　　　　　　　　　　

11 Undo the pressure
 switch

  Undo the top cover

(methods as followed).

  Pull out the plugs on the 

pressure switch.  Mind the 
position of the plug to avoid 
error during the following 
assembly. 

  Loosen the pressure switch 

hose clamp, and pull out the 
hose from the pressure switch 
interface.

  Rotate the pressure switch 

anticlockwise by 90º, and then 
pull out the pressure switch.

12 Undo the pulley

  Undo the back cover

(methods as followed).

Rotate the pulley and  at 

the same time pull out the belt, 
and then remove the belt

Remove the screw on the 

pulley and then take down the 
pulley.

13 Undo the upper 
counterweight

  Undo the top cover

(methods as followed).

Remove three screws 

fit on the upper counterweight
and then pull out the upper
counterweight

①

②

③

④

①

② 

.

③

  

①

② 

.

5.UNPACKING WAYS OF MAIN PARTS

Summary of Contents for WFL-1001



































































Reviews:

No comments

Brands by name

Popular brands

Load more brands