background image

 1  IMPORTANT SAFETY INSTRUCTIONS

This device is designed and manufactured to assure personal safety. Improper use can result in 
electric shock or fire hazard. The safeguards incorporated into this unit will protect you if you 
observe the following procedures for installation, use, and servicing.

Follow all warnings and instructions marked on the product.

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or 
aerosol cleaners. Use a damp cloth for cleaning.

Do not use this product near any liquids.

Do not place this product on an unstable surface. The product may fall, causing serious 
damage to the product.

Do not drop the product.

Do not block the slots and openings on the top and bottom of the chassis; to ensure proper 
ventilation and reliable operation of the product and to protect it from overheating, these 
openings must not be blocked or covered.

Operate this product only from the type of power indicated on the marking label.

Do not allow anything to rest on the power cord. Do not locate this product where persons 
will walk on the cord.

Never push objects of any kind into this product through the chassis slots as they may touch 
dangerous voltage points or short out parts that could result in a fire or electric shock.

Unplug this product from the wall outlet and refer servicing to qualified service personnel 
under the following conditions:

When the power cord or plug is damaged or frayed.

If liquid has been spilled on the product.

If the product has been exposed to rain or water.

If the product does not operate normally when the operating instructions are followed. 
Adjust only those controls that are covered by the operating instructions since improper 
adjustment may result in damage and require extensive work by a qualified technician to
the product to normal condition.

If the product has been dropped or the chassis has been damaged.

If the product exhibits a distinct change in performance, contact Vivaldi Customer 
Support.

Vivaldi S.R.L. it reserves the right to update this document at any time without notice.

GIOVE AC5

2

Summary of Contents for Giove AC5





















Reviews: