background image

Model # 7LIECH-SC-SSF:Page 3

IMPORTANT: Do NOT Return Dispenser To Store. 

If you have a question or problem,  please  contact 1-844-469-8482 for  

assistance

SAFETY PRECAUTIONS ---Electrical Requirements

PRODUCT FEATURES

A 120 volt, 60 Hz., AC only, 15 amp, fused electrical supply is required. A time-delay

 

fuse or circuit breaker is recommended. 

If codes permit and a separate ground wire is used, it is recommended that a qualified 
electrician determine that the ground path is adequate.

Check with a qualified electrician if you are not sure if the water cooler is properly 
grounded.

Congratulations! You have chosen an Advanced Technology State of the Art Water 
Cooler.

The refrigeration system on this cooler cools the cold water by internal evaporator of 
commercial design flat forms the ice around it. This feature is called an "Ice Bank". It 
allows for ice cold water and keeps the water temperature consistently cold, however a 
Longer time in forming the Ice Bank is required. Since ice is an insulator, the more ice is 
built up, the slower next layer is made.

WHEN UNIT IS PLUGGED IN FOR THE FIRST TIME WAIT FOR UP TO 1 HOUR FOR 
WATER TEMPERATURES TO REACH COLD TEMPERATURES. COMPRESSOR 
WILL CONTINUE TO WORK UP TO 2.5 HOURS TO BUILD UP ICE BANK.

                      Electrical shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an  adapter.
Do not use an extension cord.
Failure to follow these instructions can result in 
death, fire, or electrical shock.

WARNING

 

Summary of Contents for 7LIECH-SC-SSF

















Reviews: