VITO PRO-POWER VIMCC1400A, Instruction Manual

Page: 22 / 36

22
EN
Never use the power cable to pull,
carry or unplug the tool. Damaged
power cables increase the risk of
electric shock.
Keep the power cable and plug away
from heat sources, oil, sharp objects
and the rotating accessory. If the power
cable is damaged, it must be replaced
by a qualified technician; it is not
allowed to repair it.
Do not modify the power cable plug.
Use a compatible socket with the plug
of this equipment. Do not use any type
of adapter.
The use of extension cords to connect
the power cable is not recommended.
However, if you use an extension, you
should take some precautions, such as:
� If using this machine outdoors, use
only suitable extension cords for
outdoor use. Using a proper extension
cord reduces de risk of electric shock;
� Use only extension cords with 3
cables, plugs and sockets with earth
connection;
� The extension cable section must be
proportional to the length and have
equal or higher characteristics to this
tool’s power cord;
� Do not use damaged extension cords.
Check them before using and replace
if necessary;
� Always unplug the extension cord
before removing the equipment’s
power cable;
� When it’s an extension cord reel, unroll
the entire cable;
2.3 Before oPerating
Make sure that this tool is used only
by who is familiar with the instruction
manual.
To ensure a safe operation, you must:
� Check the entire equipment before
using it. Check that all accessories are
correctly assembled and attached to
the machine and in good conditions.
Never use damaged accessories;
� Check that all bolts are properly
tightened. A regular overhaul is
important to ensure safety and good
performance;
� After assembling the mixing paddle,
test the equipment in maximum speed
at no load for a few seconds. Verify
if there are any misalignments in the
moving parts or any condition that may
affect its normal operation. All moving
parts must spin softly without abnormal
noises or sparks in the brushes;
� Check if the safety devices are
in perfect conditions and working
correctly. Never use the machine if
any safety device is missing, inhibited,
damaged or worn;
� Ensure that the switch is off when you
plug in the power cable. If the switch is
damaged or does not allow controlling
the machine, it must be repaired or
replaced in a way to avoid a sudden
start;
� Remove any wrench or adjustment
tool before turning on the machine.
A wrench attached to the rotating
accessory may result in personal
injuries;
Perform all the needed adjustments
and in case of doubts ask your
distributor for assistance.
2.4 - WHile oPerating
Keep other people away from the
working area. Never use the tool if
animals or people, particularly children,
are nearby.
Keep the working area clean, organized
and well illuminated, in order to reduce
the risk of accidents.
Always wear personal protective
equipment. Wearing safety goggles,
safety masks, ear protection, non-slip
safety footwear, long sleeve clothing,
gloves and helmet under proper
conditions reduces the risk of injuries.
The clothing worn while operating the
tool must be appropriate and tight,
such as a work coverall. Do not wear
loose clothing or jewellery. Keep hair,
clothing and gloves away from the
moving parts.
To avoid accidents, you should also take
into account the following precautions
and procedures:
� When using the machine, place
yourself in a stable position and well
balanced. Hold the equipment firmly
with both hands to ensure a continuous
operation and to withstand unexpected
situations, such as a kickback;
� The kickback is a sudden reaction that
happens when the tool is switched on
and the rotating accessory gets stuck or
tightened. The kickback causes the tool
to be forced in the opposite direction of
the rotating accessory;
� The kickback happens due to misuse
or not suitable actions during operation.
To prevent a kickback, the following
precautions must be taken into account:
- Install and hold the rotating accessory
in the correct position and well
tightened;
- Do not position your body in the area
where the tool will be designed in the
event of kickback;
� Never place your hands near the
rotating accessory, once it may revert
over your hand. Keep hands away from
it;
� When the rotary accessory locks,
immediately turn the tool off. If you lose
control of the tool, unplug the power
cable;
� To avoid displacement or projection,
keep the container on a solid, fixed
base;