Vitek VT-8212 BK, Manual Instruction

Page: 4 / 28

4
ENGLISH
plug and carefully remove it from the mains
socket.
• Do not allow children to touch the unit body
and the power cord during the unit operation.
• This unit is not intended for usage by chil-
dren.
•
This unit is not intended for usage by peo-
ple with physical, neural and mental dis-
orders or with insufficient experience or
knowledge. Such persons may use this
unit only if they are under supervision of a
person who is responsible for their safety
and if they are given all the necessary
and understandable instructions concern-
ing the safe usage of the unit and informa-
tion about danger that can be caused by its
improper usage.
• Do not leave children unattended to prevent
using the unit as a toy.
• For children safety reasons do not leave poly-
ethylene bags used as packaging unattended.
Attention! Do not allow children to play with
polyethylene bags or packaging film. Danger
of suffocation!
• Do not attempt to repair the unit. Do not dis-
assemble the unit by yourself, if any mal-
function is detected or after it was dropped,
unplug the unit and apply to any authorized
service center from the contact address list
given in the warranty certificate and on the
website www.vitek.ru.
• Transport the unit in the original package only.
•
Keep the unit out of reach of children and
disabled persons.
THE UNIT IS INTENDED FOR HOUSEHOLD USE
ONLY, ITS COMMERCIAL USAGE AND USAGE
IN PRODUCTION AREAS AND WORK SPACES
IS PROHIBITED.
USING THE HAIRDRYER
After unit transportation or storage at low
temperature it is necessary to keep it for at
least 3 hours at room temperature before
switching on.
• Unpack the hairdryer and remove any stick-
ers that can prevent unit operation.
• Unwind the power cord completely.
• Before switching the unit on, make sure that
your home mains voltage corresponds to the
unit operating voltage.
• Insert the power plug into the mains socket.
Switching hair dryer on
Before switching the appliance on make sure
power supply voltage meets operating voltage
of the appliance.
• Insert power cord plug into wall outlet.
• Select operating speed you need using air-
flow speed switch (1):
0 = the hairdryer is switched off;
I = low speed;
II = high speed;
• Select airflow temperature you need using
heating degree switch (2).
I = slight heating
II = medium heating
III = maximal heating
Switching the ion generator on/off
To switch the ion generator on set the switch (7)
to the right, the indicator (8) will light up.
To switch the ion generator off set the switch (7)
to the left, the indicator (8) will go out.
Taking care about your hair
Before drying and setting your hair, wash them
with shampoo, dry with towel to remove exces-
sive moisture and brush for better results.
Fast drying
Set switch (2) into position of maximal heating
(position III), select airflow speed you need us-
ing switch (1) and dry your hair out a little bit.
Shake off excessive moisture by hand or using
a brush and continuously move the hair dryer
over your hair.
Straightening your hair
Set switch (2) into position of maximal heat-
ing (position III), select airflow speed you need
using switch (1) and dry your hair out a little
bit. When your hair are almost dry, install con-
centrating nozzle (6), reduce degree of air
heating by switch (2) and airflow speed by
switch (1).
Divide your hair into locks and layers and start
straightening from the lower layers. Using a
plain or a round comb, brush the hair down-
wards and simultaneously direct hot air from the
nozzle (6) at your hair. This way, slowly straight-
en each lock from root to end. After you finish
straightening the locks of the lower hair layer,
start straightening the locks of the middle layer
and finish with the locks of the upper hair layer.
IM VT-8212.indd 4 28.11.2017 17:01:16