Vitek VT-2577 BN Manual Instruction Download Page 5

Page: 5 / 24

ENGLISH

Hold the hair clipper with the blades pointed
upwards. Start cutting from the beginning of the
hair growth. Slowly move the trimmer upwards.
This way cut the head back area at neck bottom
and near the ears (pic. 3, 4, 5).

Step two

Switch the hair clipper off with the power switch
(4) by setting it to the position «

», unplug the

unit,  then  set  the  9  mm  attachment  comb  (7)
for  longer  hair  or  12  mm  attachment  comb  (8)
and  continue  cutting  hair  near  top  of  the  head
(pic. 6).

Step 3 – cutting in the temples area

Switch the hair clipper off and unplug it, then set
the 3 mm attachment comb (5) or 6 mm attach-
ment comb (6) and cut hair in the area of tem-
ples. Then set the 9 mm attachment comb (7) or
12 mm attachment comb (8) and continue cut-
ting towards the top of the head (pic. 5).

Step 4 – cutting the crown of the head

Using the 9 mm attachment comb (7) or 12 mm
attachment comb (8), cut the hair on the top
of the head towards the crown against the hair
growth direction (pic. 6).

•

You can cut hair against and along the direc-
tion of hair growth, but keep in mind that the
hair cut against the growth will be shorter
than the hair cut along the growth.

•

Use the 3 mm attachment comb (5) and 6
mm attachment comb (6) for very short hair-
cut. To leave a little longer hair, use the 9 mm
attachment comb (7) or 12 mm attachment
comb (8).

•

To leave longer hair, grip hair locks between
your fingers and cut the hair off using the
clipper (pic. 7).

•

You can use the comb: lift the hair locks
and cut them with the hair clipper above the
comb (9) (pic. 8).

•

Always start cutting from the head back.

•

Comb (9) the hair to reveal uneven locks.

•

Use scissors (10) to trim hair.

Step 5 – the final part

–

In the final stage of hair cutting remove the
attachment comb from the unit, turn the
blades of the clipper towards the hair and trim
hair on the temples and neck carefully. Do not

press the clipper strongly, there is danger of
injuries or cuts when open blades come in
contact with skin (pic. 9).

Cone-shaped haircut

Set  the  necessary  attachment  comb  and  start
cutting from the head back towards the crown.
Cut hair against hair growth from the head front
to the crown and from the sides (pic. 10). To get
a  flat  top  haircut,  use  the  comb:  lift  the  locks
and cut them along the comb. Comb the hair to
reveal uneven locks.
After  you  finish  cutting  hair,  switch  the  hair
clipper  off  setting  the  power  switch  (4)  to  the
position

«O»

and take the power plug out of

the socket, put the protective cover (1) on the
blades.

CLEANING AND CARE
Lubricating the blades

Regularly lubricate the blades using the oil (11)
supplied with the unit.

–

Switch the unit off using the power switch (4)
and unplug it.

–

Apply one-two drops of oil (11) on the teeth
of the blades and the back side of the upper
blade, switch the unit on and make sure that
the blades are moving smoothly.

–

Switch the unit off, clean the excess oil with
a dry cloth.

Attention!

Use only the oil supplied with the unit.

DO NOT USE vegetable oil, fat, oil mixed with any
solvents for lubricating.
Solvents will evaporate, leaving thick grease that
may slow down the blades’ motion.

Cleaning the hair clipper

–

Switch the hair clipper off and unplug it.

–

Clean the blades from hair, using the clean-
ing brush (12).

–

Wipe the accessories and the unit body (3)
with a slightly wet cloth, and then dry them
with a soft cloth.

–

Put the protective cover (1) on the blades.

–

Do not immerse the unit into water or other
liquids.

–