manualshive.com logo in svg

Vitec Multimedia 17245, User Manual

Share
Download
Vitec Multimedia 17245 User Manual Download Page 10

 

MGW Diamond

 

Multi-Channel HEVC and H.264 Portable Encoder 

 

User Manual, Version 1.6 

9 

 

LED/ Port 

LED Status 

Description 

Power LED 

•

 

Off 

•

 

Green 

•

 

Blinking green (once per second) 

•

 

Blinking green (twice per second) 

•

 

The appliance is off 

•

 

The appliance is up and ready 

•

 

The appliance is starting 

•

 

The appliance is being upgraded. 

Stream LED 

•

 

Off 

•

 

Green 

•

 

No stream 

•

 

Streaming 

Video In LED 

•

 

Off 

•

 

Green 

•

 

No video input 

•

 

Video input is detected on one or 
more interfaces. 

Error LED 

•

 

Off 

•

 

Blinking red (once per second) 

•

 

All services are up and running 

•

 

An error has been detected. 

USB Port 

 

USB connection for retrieving network 
parameters. 

Reset 

 
 

A short press will restart the appliance. 
A long press (6 seconds) will return the 
unit to factory settings (erasing all user-
stored channel and network settings). 
Pressing for 2-3 seconds while powering 
the appliance will re-load the last known 
good firmware. 

 

 

 

Summary of Contents for 17245




















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands