Vita-Mix 100 VAC Owner'S Manual Download Page 2

13. Always operate with the lid in place. 
14. WARNING: When processing hot liquids:

• The 2-part latching lid must be securely in place. This allows steam

to escape naturally, and will prevent the lid from coming off when
the machine is turned on.

• Use caution with hot liquids. Spraying from under the lid plug can

occur, or escaping steam may cause scalding.

• Do not process hot liquids with the non-latching lid.

15. Display window area will scratch when contacted with a scouring pad or

sharp object. Use a soft cloth to wipe the control panel area clean.

16. The optional interlock switch on some 220/240 VAC Blending Stations

®

will prevent the machine from running unless the cover door is 
completely closed.

17. The Blending Station cannot be cleaned with a water jet. 

SAVE THESE INSTRUCTIONS

2

3

1. Read all instructions.
2. To protect against risk of electrical shock, do not put motor base in

water or other liquid.

3. Close adult supervision is necessary when appliance is used by or 

near children.

4. Unplug the power cord from the wall outlet when the Touch and Go

TM

Blending Station

®

is not in use, before putting on or taking off parts, and

before cleaning other than washing the container.

5. Never contact moving parts.
6. Do not operate any appliance with a damaged cord or plug or after 

the appliance malfunctions or is dropped or damaged in any manner.
For information on a local distributor call Vita-Mix Service at 
+1(440) 235-5494. For Latin America call +1(440) 235-0214
.

7. The use of attachments not recommended or sold by Vita-Mix

Corporation may cause fire, shock, or injury.

8. Do not use outdoors.
9. Do not let the power cord hang over edge of table or counter, 

or touch hot surfaces.

10. Keep hands and utensils out of container while motor is running 

to prevent the possibility of severe personal injury and/or damage 
to the Blending Station. A rubber scraper may be used, but only 
when the Blending Station is not running. 

11. CAUTION: Blade is sharp. Handle carefully.

• Never try to remove blade while container is sitting on the motor base.
• Do not operate with loose, knicked or damaged blades.
• To reduce the risk of personal injury, never place blade assembly on

motor base without blender container properly attached.

12. The maximum normal load is equivalent to the liters listed on the

container, 2 L, 1.5 L, 1.25 L and substantially less with thick mixtures.

IMPORTANT SAFEGUARDS

Summary of Contents for 100 VAC














Reviews: