VITA FITNESS XSB42, Assembly Manual

Page: 4 / 4

ti
STEP4
XSB42-4
Now that the stall bar is square and all rung set screws are tight and still facing up, install the four wall mount
brackets (B) using the pre-installed 5/16" X 1" button head socket bolts and supplied hex wrench(�).
After all four wall brackets - are securely fastened, turn the stall bar over so that it is resting on the wall brackets.
(this may require help from another person)
, ,
Note: Your new XSB42 Stall Bar offers you three height options for the chin up bar attachment.
Once you decide on the desired height you can then install the upper wall brackets (B) in the other open_ locations.
Install the two chin up brackets (E) using the pre-installed 5/16" X 1" button head socket bolts (G)
and supplied hex wrench (J). You can choose between three outward positions for the chin up bar (4",6" & 8")
Once you decide on the chin up bar position, install the 4 bolts (G) per side. · NOTE: DO NOT FULLY TIGHTEN
THESE BOLTS AT THIS TIME.
Slide the chin up bar (D) into both chin up bracket collars, center the chin up bar so that an equal amount is
extending beyond each collar and logo name is facing outward. Firmly tighten all 8 chin up bracket bolts (G).
Firmly tighten the four pre-installed 5/16" set screws (F) on the chin up bracket collars to secure chin up bar.
-
-
0
I
I V ita Fitness
I
I
F
E
I I
0
@ ®
0
@ @
@ Cl,
@ "
CJ
[
�,
I
B
G
I
I
G
"-
"-
STEPS
Your new stall bar is now ready to be mounted to the wall. VVith the help of another person stand the
assembled stall bar up against the wall in your desired location. If mounting to a concrete, block or brick wall,
you will need to first install 5/16" (minimum) anchors at each hole location.
(concrete anchors are not included but can be purchased at most hardware stores)
If mounting to a wood or metal stud wall, you may need to add additional support blocking or backer board
rigidly secured to the wall fastening to a minimum of three studs then mount the assembled stall bar to the
support wood by first drilling a 7/32" pilot hole then fasten with the supplied 5/16" X 2-1/2" Lag Bolts and
washers (H). Note: Securely mount using all eight mounting points/ bolts.
STEPG
Push the optional decorative bolt head cover caps (I) onto the exposed bolt heads of the supplied lag
bolts (H) used to mount stall bar to the wall.
Note: Before each use confirm that bar is rigidly fastened to the wall and all hardware is tight and secure.
If you are unfamiliar with this type of work or feel uncomfortable installing this equipment we would
suggest seeking out a contractor to install for you. Vita Vibe, Inc. or it's affiliates shall not be liable
for any damages or injuries associated with the install and use of this equipment.
DISCLAIMER: As with any fitness or exercise equipment, use of this equipment should only be used by persons who are
physically able to use the equipment as it is designed for. Proper safety gear such as padded mats, shoes, clothing and
the like should always be used. This equipment should not be used alone. Always have someone nearby in case of an
emergency. Vita, Inc. and it's affiliates will not be liable for any injury or death resulting from use of this equipment. User
assumes responsibility for proper assembly, maintenance and use of this equipment.
Please keep this assembly guide for future reference. Should you need assistance
with assembly or replacement parts contact us directly. Do not return to place of purchase.
Vita, Inc. 40 Ellwood Ct. Greenville, SC 29607
Tel: 864-288-8934 Fax: 864-751-6302
Email: orders@vitavi be. com