VISSCHER 0225 Instructions Manual Download Page 43

Page: 43 / 50

2 "

BARCELONA

0225_BarcelonaAC_Instructions_V4.0

TOLL FREE: 1-877-795-7423

STEP 31

1" ROOF SCREWS

98 req

DETAIL - 1

PLACE FIVE ROOFING SHEETS ON THE ROOF STRAPS AS SHOWN. LAY

THE PIECES OUT EVENLY. PLACE THE SHEETS SO THAT THEY EVENLY
OVERHANG THE BOTTOM OF THE ROOF AND LEAVE ROUGHLY 1/2"

REVEAL ON THE TOP STRAP AS SHOWN IN DETAIL 1

MAKE SURE YOU HAVE ALL FOUR PIECES IN PLACE WITH AND EQUAL
OVERHANG OVER THE THE WHOLE EDGE OF THE EAVE. ATTACH THE
ROOF SHEETS TO THE STRAPPING WITH 1" ROOFING SCREWS.

PLACE A SCREW THROUGH EACH OF THE PRE-PUNCHED HOLES IN

THE ROOFING SHEETS. ATTACH SHEETS TO THE STRAPPING PIECES
ALREADY ATTACHED TO THE ROOF.

REPEAT THIS STEP ON TWO 14' SIDES OF THE ROOF.

NOTE:

FASTEN ALL ROOFING SCREWS PRIOR

TO STEPPING ON ROOF.

NOTE:

ONLY PUT SCREWS AT

PRE-PUNCHED LOCATIONS

DC-2160

DC-2164

DC-2161

DC-2162

DC-2163

Summary of Contents for 0225



















































Search results

Summary of Contents for 0225

Reviews:

Related manuals for 0225

Brands by name

Popular brands

VISSCHER 0225, Instructions Manual

Search results

Summary of Contents for 0225

Reviews:

Related manuals for 0225

Brands by name

Popular brands