background image

TC2-HDMIW20_manual_en 

USE ONLY DOMESTIC AC OUTLETS 

Connecting the unit to an outlet supplying a higher voltage may create a fire hazard. 

 

HANDLE THE POWER CORD WITH CARE 

Do not disconnect the plug from the AC outlet by pulling the cord; always pull the plug itself. 

Pulling the cord may damage it. If you do not intend to use your unit for any considerable 

length of time, unplug the unit. Do not place furniture or other heavy objects on the cord, and 

try to avoid dropping heavy objects on it. Do not tie a knot in the power cord. Not only could 

the cord be damaged, but a short circuit could also be caused with a consequent fire hazard. 

 

PLACE OF INSTALLATION 

Avoid installing this product under the following conditions: 

• Moist or humid places 

• Places exposed to direct sunlight or close to heating equipment 

• Extremely cold locations 

• Places subject to excessive vibration or dust 

• Poorly ventilated places 

 

Do not expose this product to dripping or splashing. DO NOT PLACE OBJECTS FILLED WITH 

LIQUIDS ON OR NEAR THIS PRODUCT! 

 

MOVING THE UNIT 

Before moving the unit, be sure to pull out the power cord from the AC outlet and disconnect 

the interconnection cords with other units. 

 

WARNING SIGNS 

If you detect an abnormal smell or smoke, turn this product off immediately and unplug the 

power cord. Contact your reseller or Vision. 

 

PACKAGING 

Save all packing material. It is essential for shipping in the event the unit ever needs repair. 

 

IF ORIGINAL PACKAGING IS NOT USED TO RETURN THE UNIT TO THE SERVICE CENTRE, 

DAMAGE IN TRANSIT WILL NOT BE COVERED BY WARRANTY. 

 

TRADEMARK 

HDMI, the HDMI Logo and High-Definition Multimedia Interface are trademarks of HDMI 

Licensing LLC. 

 

Summary of Contents for TECHCONNECT TC2-HDMIW20

















Reviews: