background image

R2100

Final Assembly

Step 7 • Console 

1:

Insert Upper Magnet Shift Cable (220) into the top 

of the Console mast (101).

2:

Mount the Console (153) to the Console Mast (101)

using the six Console Attachment Bolts (197). 

Make sure you DO NOT PINCH the Upper Magnet 

Shift Cable (220) and RPM Sensor Wire (64) 

between the Console (153) and Console Mast (101).

3:

Plug the RPM Sensor Wire (64) into the receptacle 

located on the back of the Console (153). Make 

sure the RPM Sensor Wire fits in the slot cut in the 

left side of the Console Mast (101).

Step 8 • Cable Connection 

1:

Turn the Tension Knob to position 8. Reach inside 

the opening of the Console Mast (101) and connect

the Upper Magnet Shift Cable (220) to the 

rectangular red cable-slide on the end of the 

Lower Magnet Shift Cable (66), as shown in the 

accompanying illustrations.

2:

While holding the metal separating tab (5), turn the

Tension Knob to Level 1 and then pull the tab out 

and discard.

3:

Press the Console Mast Cover (225) into the 

opening of the Console Mast (101).

Step 9 • Operation Test

Run this simple test prior to using. 

1:

Choose Intervals program, Level 8.

2:

Choose Time of “00:00”, and press Start.

3:

Your machine will now operate indefinitely. After 

several hours of operation, check for proper 

functioning of:

A: Resistance Change -- change load one 

level at a time using the dial knob on 

console. Pedal to feel for load change.

B: Check for display in RPMs while pedaling.

C: Check that all LCDs are working.

Summary of Contents for R2100









Reviews: