manualshive.com logo in svg

Vishay DXP10, Operator'S Manual, Page: 25 / 42

Share
Download
Vishay DXP10 Operator'S Manual Download Page 25

4-7 

4.1.5  Fisher ProVox Protocol 

(Optional) 

DXp-15 transmitters may be ordered with the 
Fisher ProVox protocol. Units equipped with this 
option communicate with a Fisher ProVox 
C16921 external interface card, configured for 
the 'Toledo' interface. For a further description of 
the hardware and software aspects of this 
interface, refer to BLH technical document TD-
073. 

Definitions for the byte and bit formats 
transmitted by the DXp-15 are presented below. 
To select the ProVox protocol option, DIP switch 
positions 1-3 must be set to 14,1. Baud rate is 
fixed at 4800 continuous output. 

NOTE: Hardware requirement - An external 
hardware converter is required to change the 
DXp-15 RS-485 output to 20 mA current loop for 
interface with the ProVox CL6921 card. 

FISHER PROVOX INTERFACE 

1.  TRANSMTT ONLY FORMAT - approx. 

every 200ms 

2.  BYTE FORMAT -10 BIT ASCII: 1 start, 

7 data, 1 parity - even, 1 stop 

3.  DATA OUTPUT FORMAT - 

GROSS/TARE or NET/TARE provided - 
(tare always =0) 

4.  TOTAL (RESPONSE PACKET) 

FORMAT -18 bytes - 4800 baud 

– 

continuous 

 

Summary of Contents for DXP10











































Reviews:

No comments