background image

20 / 35

 Version 1.9

Copyright ©

eco-CONTROL EC200-B

Operation and maintenance instructions

9.   

Select External 

and confirm, the input dialog to 

determine the quantity appears, display 39.

D

is

pl

ay

 1

8

10.  

Create an external signal

 (e.g., press the foot switch), the 

dispenser is started up. 

11.  Once the dosing quantity has been reached, switch off 

the 

external signal

. The dosing quantity is displayed, 

accept it with 

OK

.

   

   

   

   

 D

is

pl

ay

 3

9

12.  Press the 

STOP

 key, 

OK

 is offered to save the dosing 

quantity.

13.  Confirm with 

OK

, the dosing quantity is saved and 

display 3, 

Quantity program

, appears with the saved 

quantity.

D

is

pl

ay

 3

Note:

 Since the flow rate in the Teach in function can differ from the flow rate in the 

program that is used subsequently, we recommend that you next check this and 

make any necessary corrections if there are especially tight requirements concerning 

the dosing quantity.

5.10.2 Dosing time

1.   Press the 

Quantity program 

shortcut key, display 10 

appears.

2.   Set, confirm and save the dosing time.

The set value remains active until the next change or until 

the Dosing systems is switched off. Alternatively, a value of 

its own for the flow rate can be assigned to each dosing 

program (See 5.14, Changing a dosing program, page 29).

D

is

pl

ay

 1

0

5.10.3 Flow rate

The flow rate can be set in each dosing program. The maximum flow rate 

that can be set is: 

eco-PEN300  1,48 ml/min; eco-PEN450 6 ml/min;  eco-PEN600 16 ml/min

•   Selecting, changing and saving the displayed value.

The bar chart shows in what range (%) the flow rate is. 

D

is

pl

ay

 3

4

Esc

NAVI-wheel

Teach in function

select signal

External

Quantity program

Esc

Suckback

Flow rate

Volume

0%

100%

ml/min

00.100

03.000

00.000

ml

ml

Summary of Contents for Preeflow eco-CONTROL EC200-B





































Reviews: