ViscoTec Preeflow eco-CONTROL EC200-B Operation And Maintenance Instructions Download

Page: 17 / 36

Version 1.9

17 / 35

eco-CONTROL EC200-B

Operation and maintenance instructions

Selection whether the calibration is to be done with quantity

unit

(

µl

)

(mg)

and confirm this, the set quantity can

be set as desired.

* If the saved density value corresponds to the value

1.000 g/cm³ (default value), the input dialog for the material

density appears when you select

(mg)

. See 5.10.5,

Material density, page21.

• Set and confirm the set quantity.

The value preset in the Dosing system is to be regarded as the ideal value.

• Position the calibration vessel underneath the outlet nozzle (dosing needle) of the

dispenser.

• Press the

START

key, the calibration starts, the dispenser is switched on and

conveys the quantity specified by the system. This process can be repeated as often

as desired. e.g., for comparative measurements.

• The ACTUAL amount that goes into the calibration vessel is determined in the

previously set measuring unit. See also 5.10.1, Dosing amount.

• Input and confirm the ACTUAL quantity that has been determined.

• Select the OK button and confirm, the next dialog to save the calibration value

appears (display 17.1).

• Accept or discard the suggested program slot, confirm this,

and the system has been calibrated.

5.9.2

Calibration manual

The

Calibration manual

function provides a simplified option to recalibrate the system

without having to run through the entire process in the

Calibration auto

menu.

This can be helpful, for example, after changing the stator, in the event of batch-

related product variations, etc., whereby the set dosing value is not to be changed

(QA documents, etc.).

Caution:

Setting the flow rate in the

Calibration manual

menu also changes the

dosing results of all the dosing programs by a linear factor.

• Press the

PRG

key,

system selection menu

, display 2

appears.

• Select and confirm

Calibration manual

, the

Calibration

manual

menu, display 40 appears.

Press Start

Esc

Calibration auto

Desired qty

Actual qty
Flow rate

00.500 ml

middle

00.000 ml

Save with OK

Esc

Calibration auto

Save calibration value
at prog. no.: 00

Start/stop
Time program
Calibration auto
Calibration manuel
Teach in function
Administration

Quantity program

10 47h

Fr 18.03.11

Service

Esc OK

Summary of Contents for Preeflow eco-CONTROL EC200-B





































Search results

Summary of Contents for Preeflow eco-CONTROL EC200-B

Reviews:

Related manuals for Preeflow eco-CONTROL EC200-B

Brands by name

Popular brands

ViscoTec Preeflow eco-CONTROL EC200-B, Operation And Maintenance Instructions

Search results

Summary of Contents for Preeflow eco-CONTROL EC200-B

Reviews:

Related manuals for Preeflow eco-CONTROL EC200-B

Brands by name

Popular brands