manualshive.com logo in svg

Viptela vEdge 100wm Series, Manual, Page: 8 / 30

Share
Download
Viptela vEdge 100wm Series Manual Download Page 8

Table 4:

Status

Color

LED

• Off: System is not on

• Green: System power is healthy and operational

• Red: Power supply fault

Green/Red

Power

• Off: System is not on

• Solid Green: System is fully functional

• Blinking Green: System is booting up

• Solid Yellow: No Internet connectivity or the system has detected

a minor alarm

• Red: System has detected a major system level fault or alarm

Green/Yellow/Red

System

• Off: No link

• Solid Green: 1000 Mbps link detected

• Blinking Green: 1000 Mbps link detected and link activity

• Solid yellow: 10/100 Mbps link detected

• Blinking Yellow: 10/100 Mbps link detected and link activity

Green/Yellow

Ethernet Port
(LED 0–4)

• Off: WiFi interface disabled/off

• Solid Yellow: WiFi enabled

• Blinking Green: WiFi client connected and link activity

Green

WiFi Status

• Off: LTE interface disabled/off

• Solid Green: LTE enabled, excellent signal strength, dormant

mode

• Blinking Green: LTE enabled, excellent signal strength, active

mode

• Solid yellow: LTE enabled, good signal strength, dormant mode

• Blinking Yellow: LTE enabled, good signal strength, active mode

• Solid Orange: LTE enabled, poor signal strength, dormant mode

• Blinking Orange: LTE enabled, poor signal strength, active mode

• Solid Red: LTE enabled but faulty such as no connectivity with

BTS, errors, or no signal

Green/Yellow/Red

WWAN Signal
Strength

Figure 1 shows the location of the chassis status LEDs on the front panel of the vEdge 100wm router.

vEdge 100wm Router

8

vEdge 100wm Router

Front and Rear Panel Components

Summary of Contents for vEdge 100wm Series































Reviews:

No comments