background image

Operator's Manual

Viper® 99cc 4-Cycle Engine

8

For additional information email 

[email protected]

 or call 800-345-6007 M-F 8-5

OPERaTION

PRE-OPERaTION INSPECTION

1.  Check that the engine is equipped with the proper amount 

and type of oil.  To determine the most appropriate type of 

oil to use, see the chart below.  

2.   Check that the engine has appropriate amount of fuel.
3.  Examine underneath and around engine for signs of oil or 

fuel leaks.

4.  Inspect fuel hoses and connections for tightness and fuel 

seepage.

5.  Look for signs of engine damage.
6.  Check that all guards and shields are in place, and all screws, 

nuts and bolts are tightened.

7.  Eliminate excessive debris around muffler and recoil starter.
8.  Be sure air filter and cylinder fins are clean and free of debris.
9.  Check the equipment powered by this engine.  Review the 

operator’s manual provided with the equipment powered 

by this engine for any safety and warning precautions and/

or procedures that should be followed before starting this 

engine. 

Choosing Oil Type

 

WaRNING

DO NOT aTTEmPT TO STaRT ENGINE IN THE FOllOW-

ING WaYS:
•  DO NOT use sTarTiNg fluiD.
•  DO NOT spray flammable liquiDs Or vapOrs 

INTO aIR ClEaNER, CaRBURETOR OR SPaRk PlUG 

CHamBER.

•  DO  NOT  remOve  spark  plug  aND  pull  ON 

STaRTER ROPE. FlammaBlE FUEl CaN SPRaY OUT 

aND IGNITE FROm a SPaRk FROm SPaRk PlUG.

DO NOT REFUEl WHIlE SmOkING, NEaR OPEN FlamE, 

OR OTHER POTENTIal HaZaRDS.
FUEl IS HIGHlY FlammaBlE aND mUST BE HaNDlED 

WITH CaRE.  NEVER FIll THE TaNk WHEN THE ENGINE 

IS HOT OR RUNNING.  alWaYS mOVE OUTDOORS TO 

FIll TaNk.

 CaUTION

FOR THE SaFETY OF THE USER, aND TO maxImIZE 

THE lIFE OF THE ENGINE, IT IS CRUCIal TO TakE TImE 

TO CHECk THE CONDITION OF THE ENGINE.  PROB-

lEmS mUST BE CORRECTED BEFORE OPERaTING.
aVOID INJURY!  ENGINE OIl IS HaZaRDOUS TO YOUR 

HEalTH.  DISPOSE OF OIl aPPROPRIaTElY.   USE a 

SaFE DISPOSal/RECYClING CENTER.

 CaUTION

ENGINE IS SHIPPED FROm FaCTORY WITHOUT OIl.  

YOU mUST aDD ENGINE OIl BEFORE STaRTING EN-

GINE.

 WaRNING

ImPROPERlY maINTaINING THIS ENGINE, OR FaIl-

URE TO CORRECT a PROBlEm BEFORE OPERaTION, 

CaN CaUSE a malFUNCTION WHICH maY RESUlT 

IN SERIOUS INJURY OR DEaTH.  alWaYS PERFORm a 

PRE-OPERaTION INSPECTION BEFORE EaCH OPERa-

TION aND CORRECT aNY PROBlEm.

OIL TYPE:

 SAE 5W-30

OIL TYPE:

 SAE 10W-30

OIL TYPE:

 SAE 30

TEMP (F)

      -20          0          20        40         60        80        100

TEMP (C)

   -30      -20      -10        0         10        20       30

Summary of Contents for 13276

























Reviews: