VIPColor VP6 Series User Manual Download

Page: 52 / 84

Printer Maintenance

5. Pull the service station forward until you can disconnect the flex cable to the

wiper motor. Loosen the clip on the connector (

) to release the flex

cable.

Ensure that the flex cable does not come into contact with any metallic
surface. If it is touching metal and the printer is accidently turned on, it will
short the controller circuit and damage the printer.

Take care when handling the service station. Ink may spill when you tilt the
service station.

NOTE:

Dispose of the old service station according to local regulations.

Installation

6. Insert the flex cable into the connector on the new service station and push in the

clip to secure it.

Figure 11

Flex cable to connector on service station

flex cable

clip

flex cable

Summary of Contents for VP6 Series





















































































Search results

Summary of Contents for VP6 Series

Reviews:

Related manuals for VP6 Series

Brands by name

Popular brands

VIPColor VP6 Series, User Manual

Search results

Summary of Contents for VP6 Series

Reviews:

Related manuals for VP6 Series

Brands by name

Popular brands